Overview

Section A: Hardware setup

  1. Connect to your charger's wifi network “EnelionChargerXXX”

  2. Open up internet browser to 192.168.8.8

  3. Log into the admin panel

  4. Open the side menu, select "System" and then "Overview"

  5. Find the serial number and create an identifier

  6. Go to the OCPP section

  7. Select "Connect to Specified Management System"

  8. Navigate back to the menu, select "System"

  9. Now click on "Reboot"

  10. Proceed to the Monta Portal

Section B: Setting up in the Monta Portal

  1. Add Charge Point

  2. Add Charge Point Settings

  3. Add Charge Point Details

  4. Connect to Monta

  5. Select Brand

  6. Select Model

  7. Select Integration Method

  8. OCPP Integration

  9. Check Connection

  10. Verifying

  11. Perfecto! You are now connected to Monta!

Section A: Hardware setup

You first need to integrate your charger with Monta. This will make us the operator of your charge point. This means we will have control of your charge point and from now on you should use us to start or schedule a charge on your car.

Step 1: Connect to your charger's wifi network “EnelionChargerXXX”

You need to first connect the device you are going to perform the integration on (phone, tablet, computer, etc.), to the wifi network, named after your charger.

  • Open up internet browser, type in this IP 192.168.8.8 and hit ‘go’ or ‘enter’

! Please note ! that the following screenshot is an example of a wifi name. Every charge point will have different numbers in the end of the name.

Step 2: Open up internet browser to 192.168.8.8

Step 3: Log in to the admin panel

To log in to the admin panel, please use the following credentials.

Username: admin

Password: admin

Step 4: Open the side menu, select "System" and then "Overview"

Step 5: Find the serial number and create an identifier

  • From the serial number field, copy only last four digits.

  • Create an identifier (from now on regarded as serial number) by adding the four digits to the word "ENELION"

This is now the serial number for this charge point. In the current example the serial number would be ENELION0196. Write this down, as you will need it in the next steps.

Step 6: Go to the OCPP section

Step 7: Select "Connect to specified management system"

  • In the OCPP address section copy this address: wss://ocpp.monta.app/

  • In the StationID section write the Serial number, which you created in step 2.e. (ENELIONxxxx)

Step 8: Navigate back to the menu, select "System"

Step 9: Now click on "Reboot"

Please note that you have to wait until the reboot has finished. This process can take several minutes.

Step 10: Proceed to the Monta Portal

Now that you have completed the Hardware Setup of your charger, you can proceed to the Monta Portal.

Section B: Setting up in the Monta Portal

Before setting up in the Monta Portal create the team. Here you can find information about how to create the team on Monta Portal and where to add your Enelion charge point.

1. Add Charge Point

On Monta Portal click on "Add charge point" under Teams section.

2. Add Charge Point Settings

Select Enelion and the charge point model, put max charging power (this information can be find on the charge point box or should have been provided by the manufacturer in this case Enelion) and choose supported connector type.

3. Add Charge Point Details

You can add an existing Charge point group or create one for that specific location. If you already have a Charge point group pointing to that location of the charge point it will be added automatically.

4. Connect to Monta

Important! If you choose "Not now" you can connect your charge point to Monta later. Click on Charge Point Name - Set Integration.

5. Select Brand

6. Select Model

7. Select Integration Method

8. OCPP Integration

Important!! At this point of installation you will need to have the charge point serial number. When you reach this part of charge point integration portal will automatically fill in the serial number field for you. Please click on the option "I have my own serial number".

After clicking on that option, you will get the screen below, where you can input your own charge point's serial number.

9. Check Connection

10. Verifying

Here we verify your connection to Monta. Please wait until the loading bar reaches 100%.

11. Perfecto! You are now connected to Monta!

Congrats! 🤗 You have now successfully installed your Enelion charge point to Monta.

Did this answer your question?