Overview

Section A: Hardware setup

  1. Connect to your charge point

  2. Open an internet browser to 172.20.0.1

  3. Click on "Network"

  4. Click on "Backend" and fill out information

  5. Check the Authorization details

  6. Restart the charge point

Section B: Setting up in the Monta Portal

  1. Add Charge Point

  2. Add Charge Point Settings

  3. Add Charge Point Details

  4. Connect to Monta

  5. Select Brand

  6. Select Model

  7. Select Integration Method

  8. OCPP Integration

  9. Check Connection

  10. Verifying

  11. Perfecto! You are now connected to Monta!

Section A: Hardware setup

First, you need to setup the charge point configuration.

You need to have Webasto manual ready, which you have received it together with your charger. There you will find all necessary passwords. If it happens that you don't have a manual, it will take around 2 weeks to send a new manual to you.

Webasto LIVE will need internet connection to take full advantage of the box's features. Internet connection with your box can be obtained via wifi, a network cable or 4G network via a SIM card is also an option (contact Webasto DK if desired).

1. Connect to your charge point

Establish connection with your charge point via wifi or use a cable. Log in to the box's hotspot - wifi signal - you will find the password in the manual.

WLAN SSID: Webasto!Live xxxxxxxxxxxx (x would be numbers)
WLAN Password: xxxxxxxxxxxx

2. Open an internet browser to 172.20.0.1

Enter 172.20.0.1 in a browser's address bar and log in. You will find the password in the manual.

Portal Password: xxxxxxxxxxxx

3. Click on "Network"

You will have to have wireless internet name and password used in the location.

As mentioned earlier you have three possibilities to connect your charge point, via Wifi connected, internet cable or GSM 4 G card. Here in this guide we are connecting it using wireless internet connection.

Here enter the name and code used - make sure it is correct!

4. Click on "Backend" and fill out information

  • Choose connection type: WLAN

  • Under OCPP ChargeBoxIdentity (ChargePointID) - delete any letters or signs you may see and leave only the numbers.

  • Under WebSockets JSON OSPP URL of the Backend - insert (paste) this address: wss://ocpp.monta.app/

  • Click on save

    5. Check the Authorization details

    In addition go to Authorization and ensure the Settings are as follow:

    Free Charging: Off
    If in doubt allow charging: Off
    Vehicle connection timeout: 180
    Send Authorize for RemoteStart: On
    RFID Tag letter case: Uppercase
    Enable local whitelist: Off
    Local whitelist learning mode: Off
    Enable OCPP Whitelist: On

6. Restart the charge point

Now you will be requested to restart the charge box.

After restarting, wait for 5min and go back to Monta App to finish the integration.

Section B: Setting up on the Monta Portal

Before setting up in the Monta Portal create the team. Here you can find information about how to create the team on Monta Portal and where to add your charge point.

1. Add Charge Point

On Monta Portal click on "Add charge point" under Teams section.

2. Add Charge Point Settings

Select Webasto and the charge point model, put max charging power (this information can be find on the charge point box or should have been provided by the manufacturer in this case Webasto) and select supported connector type.

3. Add Charge Point Details

You can add an existing Charge point group or create one for that specific location. If you already have a Charge point group pointing to the location of the charge point it will be added automatically.

4. Connect to Monta

Important! If you choose "Not now" you can connect your charge point to Monta later. Click on Charge Point Name - Set Integration.

5. Select Brand

6. Select Model

7. Select Integration Method

8. OCPP Integration

Important!! At this point of installation you will need to have the charge point serial number. Add Charge Point identifier and click on "Done, what's next?"

9. Check Connection

10. Verifying

Here we verify your connection to Monta. Please wait until the loading bar reaches 100%.

11. Perfecto! You are now connected to Monta!

Congrats! 🤗 You have now successfully installed your charge point to Monta.

Did this answer your question?