Powered by Monta makes the installation process much faster and smoother. Follow this quick guide to learn how to add and connect your LinkCharging charge point to the Monta system.

This is a guide that shows how to install Monta on your charge point. If you want to connect your charge point to your Monta account, please follow the steps in the end of the guide.

Please note that when you connect your charge point to Monta, we become the operator of the charge point. This means that you need to use Monta to control the charging process.

Overview

  1. Prerequisites

  2. Connect the USB cable

  3. Open your browser to http://192.168.7.2

  4. Access the "Configuration" section and enable "Advanced settings"

  5. Select the "Interface" tab

  6. Configure the charge point

  7. Open the "Authorization settings" subsection

  8. Enable "RFID lock"

  9. Confirm authentication mode

  10. Reset the charge point

  11. Check the "Status" section

  12. Scan the QR sticker

  13. Fill in the charge point details

  14. Wait to connect

  15. Congrats, you have connected your charge point to Monta!

1. Prerequisites

If your computer runs on Microsoft Windows, download the CCU Drivers from the website. Follow the instructions given on the website.

CCU Driver for Windows

For Linux, Android and Mac OSX, the USB driver is part of the operating system.

When CCU drivers are installed, it is now possible to configure the controller board of the charge point.

2. Connect the USB cable

Connect the USB cable between the computer and the mini USB port on the controller board.

3. Open your browser to http://192.168.7.2

Open the web browser and log into the local web interface at http://192.168.7.2

Username: ccu

Password: ccu

4. Access the "Configuration" section and enable "Advanced settings"

Once you are inside, select the "Configuration" section from the left side menu.

After this, click on the "Setup" tab from the top menu and slide the "Advanced settings" toggle.

5. Select the "Interface" tab

Open the "Interface" tab from the top menu.

From the drop down "WAN" menu select "Wired". Then, click and open the "Wired" subsection.

6. Configure the charge point

From drop down "Configuration Method" menu, select "DHCP".

If DHCP is not supported by your router, enter the network settings manually.

After you make this setting, click on "Save".

7. Open the "Authorization settings" subsection

In "Authorization settings", make sure that the charge point has the correct settings, as shown in the screenshot bellow.

Stop transaction on invalid ID - On

Authorization Cache - Off

Authorize Remote Tx Requests - On

Allow Offline Tx For Unknown Id - Off

Local Authorize Offline - On

Local Pre Authorize - Off

Allow Offline Tx Without Id - Off

Local Authentication List - On

Make sure to click on "Save".

8. Enable RFID lock

Navigate to the "General" tab on top. Make sure that RFID lock is enabled.

This is mandatory for the Monta connection to work.

Click on "Save".

9. Confirm authentication mode

Now navigate to "Outlets" and make sure that Authentication Mode is "RFID".

If you see "Open", please open the drop-down menu and select "RFID" and click "Save".

10. Reset the charge point

Once you save all changes, click on the "Reset" button in the pop-up window that appears on top of the screen.

11. Check the "Status" section

Open the "Status" section from the left side menu.

Check to see if "Backend connection" and "WAN connection" are established.

11. Scan the QR sticker

Open the charge point box and find the QR sticker inside.

Point the camera of your phone at the Monta QR sticker and scan it.

When you scan the QR code on the charge point, you will be prompted to open the Monta app. If you do not have the app yet, you will see how to download it.

Click on the "Open" button.

12. Fill in the charge point details

After scanning the QR code on the charge point, the Monta system has already recognized the charge point brand and model.

Enter the name and location of your charge point and select which team you want to register it in. Then click on "Connect to Monta".

13. Wait to connect

Here, our system is checking if your charge point is online and is trying to connect to it.

14. Congrats, you have connected your charge point to Monta!

You have successfully connected your charge point with Monta.

🎉 Happy charging!🎉

Did this answer your question?