Skip to main content
Test Report Entry
Updated over a week ago

Access: Service Providers

Overview: Basics on entering submitting backflow test reports, adding a new facility, and adding a new assembly.

Topics:

Navigating to the Test Reports Tab

To get to the Test Reports Tab, go to the left side of your screen and select Test Reports on the navigation panel.

Screen_Shot_2021-09-08_at_11.34.21_AM.png

Entering a Test Report

To enter a test report, click on the Test Reports tab on the left side of the screen, then click the green New Test Report button at the top right.

Screen_Shot_2021-09-08_at_11.36.24_AM.png

Type in the address of the facility where the assembly is located or enter the assembly serial number.

Screen_Shot_2022-08-15_at_11.51.53_AM.png

Pro Tip: You can type in a partial address and/or location name and your results will still appear!

Pro Tip: If you are unable to find your device by serial number search, try search by location before creating a new device!

Now click the green magnifying glass to complete your search. This will bring up all available assemblies at this location.

Next, click on the assembly that you want to submit a test for and click Continue to Service Provider Selection.

Pro Tip: If you don’t see the assembly you’re looking for, refer to the “Entering a New Assembly” section of this guide.

Screen_Shot_2022-03-01_at_9.23.19_AM.png

Select the service provider that you worked with to complete this test, the tester that completed the test, and select the appropriate test kit.

FINAL_SwiftComply_Backflow_Tester_Training_Doc.png

Confirm the location and assembly information is correct and click Next.

FINAL_SwiftComply_Backflow_Tester_Training_Doc.png

Fill out the Test Data form and click Next.

FINAL_SwiftComply_Backflow_Tester_Training_Doc.png

Confirm that the Test Summary and Tester Info data is all correct and click Submit & Save to submit your test, or click Save so you can come back and finish entering later.

FINAL_SwiftComply_Backflow_Tester_Training_Doc.png

Confirm that all information you’ve entered is correct by clicking Yes.

FINAL_SwiftComply_Backflow_Tester_Training_Doc.png

When the test is submitted, you’ll be taken back to the Test Report screen, and the status of Pass or Fail (determined by the system validation) will be listed under the Result column of the Test Report Table.

**Please Note: Each water organization has their own unique test form based on their local requirements. Because of this, your test form differs from the one in this example.

FINAL_SwiftComply_Backflow_Tester_Training_Doc.png

On each page of the test report entry process, you'll see a paperclip at the top right corner of the screen. Clicking this will allow you to attach documents that are applicable to that section of the test report.

To attach your file, click Choose File and find the file on your computer that you're wanting to attach. Then select the drop-down menu to choose what field you want your file associated with. Finally, you'll click Upload to attach the file.

tempsnip.png
tempsnip.png

Entering a New Location/ Assembly

If the address of the facility you’re searching for isn’t showing up, click I'm at a brand new location or I have an assembly I just installed below the search fields.

Screen_Shot_2022-08-15_at_11.56.19_AM.png

Follow the same steps above to complete your backflow test submission filling in all necessary location and assembly information.

Auto-Fill Settings by Browser:

Autofill is a tool that most if not all web browsers have that helps to eliminate the need to type or enter your contact information into address and contact fields when requested.

When used correctly, Auto-Fill can greatly reduce data entry time! For Example, when entering tests when you get to the confirmation page you will be prompted
for the test company name and address, auto-fill can greatly reduce the data entry
time in these areas.

Screen_Shot_2022-10-13_at_2.02.56_PM.png

When you click on one of the name or address fields your information may already
be in auto-fill.

If it is, all you have to do is click on it and the fields will be filled in. If it is not however or needs to be edited, these are the steps to take to enable auto-fill on Google Chrome, Firefox, and Microsoft Edge.

Google Chrome

Screen_Shot_2022-10-13_at_2.08.44_PM.png
  • In the upper right-hand corner of the Chrome web page, you will see 3 dots in a row.

Screen_Shot_2022-10-13_at_2.11.37_PM.png
Screen_Shot_2022-10-13_at_2.12.58_PM.png
Screen_Shot_2022-10-13_at_2.14.13_PM.png
Screen_Shot_2022-10-13_at_2.15.03_PM.png
Screen_Shot_2022-10-13_at_2.16.46_PM.png
Screen_Shot_2022-10-13_at_2.17.31_PM.png
Screen_Shot_2022-10-13_at_2.18.17_PM.png

Firefox

Screen_Shot_2022-10-13_at_2.19.13_PM.png
Screen_Shot_2022-10-13_at_2.20.23_PM.png
Screen_Shot_2022-10-13_at_2.22.10_PM.png
Screen_Shot_2022-10-13_at_2.23.13_PM.png
Screen_Shot_2022-10-13_at_2.25.54_PM.png
Screen_Shot_2022-10-13_at_2.30.41_PM.png

Microsoft Edge

Screen_Shot_2022-10-13_at_3.22.52_PM.png
Screen_Shot_2022-10-13_at_3.24.11_PM.png
Screen_Shot_2022-10-13_at_3.25.10_PM.png

Safari

In the upper left corner of your Apple device, click on the Preferences option.

Screen_Shot_2022-10-21_at_12.58.09_PM.png

Next, locate the autofill tab

Screen_Shot_2022-10-21_at_12.58.54_PM.png

Here you can edit autofill for credit cards, names, and more by clicking "Edit" to add new details.

Did this answer your question?