Skip to main content

How to set what a rule does

Add an action, write the conditions that trigger it, and set how often it may act on the same item.

Written by Team adnova

A task is one action, such as Pause, plus the conditions that have to be true before it runs. A rule can hold several, so one rule can boost winners and trim losers on the same check.

Add a task

  1. In the rule builder, open the Tasks section.

  2. Click Add Task.

  3. Choose an action. The panel beside the list describes it and shows its settings.

  4. Set the action's values, for example the percentage for a budget change.

  5. Set Frequency. This is a cooldown, not a schedule, and it is explained below.

  6. Click Save task.

  7. Add the conditions on the task card.

How to tell it worked

The Tasks step in the Rule Flow shows a count, and the task card shows your action with its conditions underneath. Click Preview Conditions to read them back as a sentence.

Write the conditions

A condition is a metric, a comparison, a value and a time window.

  1. Click Add Condition on the task card.

  2. Click the metric field and choose a metric.

  3. Choose a comparison and type a value.

  4. Choose a time window.

The picker here is much richer than the filter's. It holds the whole Meta catalogue, plus Adnova's Hook score and Watch score, and the Custom and Integrations tabs for your own formulas and connected analytics tools.

Metric level lets a rule acting on ad sets test the parent Campaign or the Ad Account numbers instead. That is how you write "pause this ad set if the whole campaign is underwater".

The right-hand side of a condition does not have to be a number. It can be another metric over its own time window, which is how you test "worse than its own average" rather than a figure that dates. See How to compare one metric with another.

Several conditions can be joined with AND or OR, and + Add Group nests one set of logic inside another. See How to combine conditions with AND, OR and groups.

Set Frequency, the setting people miss

Frequency on a task is not how often the rule checks. It is how often that task may act on the same item.

A rule that checks every 15 minutes with a task set to Once a day looks at an ad set 96 times a day and acts on it at most once.

Match it to the decision, not to the schedule.

Decision

A sensible Frequency

Pausing something

Once a day. You do not want a rule pausing and unpausing as numbers wobble.

Raising a budget on a fast account

Once an hour.

Cloning an item

Only once, so each ad set is duplicated a single time, ever.

Almost anything else

Once a day or slower. Very few decisions need Every check.

The full list runs from Every check through 15 minutes, 30 minutes, an hour, 3, 6 and 12 hours, a day, 3 days and a week, to Only once.

Only once is the one worth knowing. It means once per item for the life of the rule, not once overall, so a Duplicate task set to Only once clones each ad set a single time however long the rule runs.

Not every action offers Frequency, and the ones that do not are the ones that gain nothing from it. Start, Pause, Archive, Set bid strategy, Add to name, Remove from name and Replace in name have no cap, because repeating them changes nothing: pausing an already-paused ad set is not a second pause. The cap exists for the actions that compound, such as budget and bid changes and Duplicate.

If you want a rule with a Pause task to skip items it has already handled, tag them with Add to name and add a name filter that excludes the tag. See Common ways to use Ad Automation.

When the cooldown holds a task back, the logs say so against that item, in these words: "This task already acted on this item recently, so it was held by its frequency cap."

The actions you can choose

Group

Actions

General

Start, Pause, Archive, Duplicate, Notify, Extend end date

Budget

Increase budget, Decrease budget, Set budget, Scale budget by target

Bid

Increase bid, Decrease bid, Scale bid by target, Set bid, Set bid strategy

Spending limits

Increase spending limit, Decrease spending limit, Set spending limit, Remove spending limit

Naming

Add to name, Remove from name, Replace in name

Archive is switched off for the beta. It still appears in the list and says so, and rules that already archive keep running.

Actions that do not apply at your level are greyed out. Three worth calling out:

  • Notify changes nothing on Meta. It messages whoever is listed in Notification Settings, which makes it the safe way to trial a rule.

  • Scale budget by target and Scale bid by target move the number toward a figure you name, rather than by a fixed step.

  • Add to name tags items, for example appending #fatigued so you can filter on it later.

Attribution window

In the Settings section, Use ad set attribution window decides how many days after a view or click a conversion still counts. Leaving it ticked keeps the rule in step with Ads Manager, which is usually what you want.

Common questions

My rule matched ad sets but changed nothing. The conditions did not fire. Open the check in the logs; each item shows the value that was tested.

Meta has no field for what I want to test. Build one. See How to create and use a custom metric.

Next

Did this answer your question?