Skip to main content

Troubleshoot: a rule is not doing anything

Find the message the logs are showing you, and the one thing that fixes it.

Written by Team adnova

Almost every "my rule is not working" is one of a handful of things, and the logs name which one.

Start here

  1. Go to Paid Media > Ad Automations > Rules.

  2. Check the Status column. If it says Draft, the rule has never been switched on. Turn on its toggle and you are done.

  3. Otherwise click Logs on the rule.

  4. Read the Result of the most recent check.

  5. Find that message in the table below.

Match the message to the fix

The logs say

What is wrong

What to do

Nothing matched

No item got past the filter.

Open the rule's Filter section and click Estimate. If it says zero, the filter is too narrow or pointed at the wrong level.

Nothing was changed

Items matched, but no condition fired.

Click into the check. Each item shows the value that was tested, so you can see how close it came.

ROAS 1.2, needed below 1 on an item

That item was judged and did not qualify.

Nothing is broken. Your threshold is simply not being crossed.

This task already acted on this item recently, so it was held by its frequency cap.

The task's cooldown.

Open the task and look at Frequency. It is how often a task may act on the same item, not how often the rule checks.

Waiting for approval

The rule is waiting on a person.

Go to Automation > Approvals.

Watching only, so nothing was changed

The rule is in watching mode by design.

Nothing is broken. Take the rule out of watching when you want it to act.

Nothing to change

The item was already in the state the task wanted.

Nothing to do. Pausing something already paused changes nothing.

Did not run, rule paused

The rule was off when its turn came.

Turn on its toggle.

Did not run, Meta limited this ad account

Meta was rate limiting.

Nothing to fix. The rule checks again on its next schedule.

Meta refused this check: ... (#17)

Meta was asked and said no.

The code in brackets is Meta's. Rate limits clear by themselves. Permission errors need the ad account reconnected.

The check failed: ...

Something went wrong on Adnova's side.

We are told automatically. If it keeps happening, send us the rule name and the time.

Reconnect the ad account inside a failure

The connection to Meta has lapsed.

Reconnect the account. See How to manage connected ad accounts. Editing the rule will not help.

The toggle will not switch on

Hover it and it tells you why.

"Your organization has no active Adnova plan." Rules can be built and saved without a plan, but not run.

The rule is Watching. The toggle is locked on purpose, because a watching rule reports and never acts.

The rule says Needs Attention

A check could not run, and usually it is not something you caused. Adnova is told automatically and the rule tries again. After three failed checks it stops itself, and pressing its toggle clears the fault.

Read the red line under the row first: it is the reason for this stop. If it asks you to reconnect the ad account, switching the rule on without reconnecting only earns it another stop.

The numbers are not what you expect

Metrics follow the ad account's day and its attribution window, not your local day.

  1. Open the rule and go to the Settings section.

  2. Read the Three Clocks panel. A rule reading "today's spend" reads Meta's day for that account, which may be nearly over or barely started relative to yours.

  3. Check Use ad set attribution window. Conversions outside it do not count.

An approval expired

Open Automation > Approvals. "Nobody answered, so nothing was changed" means it timed out. "No longer applied" means the approval came through after the numbers moved, so the action was correctly skipped rather than applied to stale data.

Still stuck

Send us the rule name and the time of the check through the messenger. We can see the same logs you are looking at.

Still matching nothing?

Check whether the filter is on Status when it should be on Delivery, or sitting on a value that never matches. See How to filter by status and delivery.

Next

Did this answer your question?