Give each zone of a Phase Spatial zone map a rate and export a variable-rate (VRT) file for your spreader, seeder or sprayer. You can also send the average to Crop Plan Studio, save versions and reuse the setup on other paddocks. Phase doesn't choose rates: you decide them.
Exporting a VRT file, in short. In More → Paddocks & crops → Spatial, build the zones. On the Prescription step, choose the product and give every zone a rate (0 to skip one). Select Export on the step bar at the foot of the map, choose Prescription (Rx) and Shapefile, and select Export prescription. Phase can't send a prescription straight to a machine or to John Deere Operations Center.
Before you start
Spatial comes with Phase Ultra and the free trial.
The paddock needs a zone map: the Prescription step stays locked until zones are built. See Build and edit a zone map.
Rates are optional. A zone map with no rates can still be saved, and exported as a Zone map.
Saving, or updating the crop plan from Spatial, needs permission to edit crop plans. If you can't save, ask a farm owner.
Choose the product and unit
On the Zones step, select Set rates on the step bar, or select Prescription in the steps across the header. The rates open in the column beside the map. On a phone they open at half height, so the zones stay on the map above them, and the dock tab becomes Rates. Zones are ordered by the main layer: zone 1 is the bottom zone and the highest number is the top zone. Each zone shows the readings it covers (for example "4.8–5.2 pH") and its hectares.
Under 1 · Product, select Choose a product…. Product for this map opens with your own products first and the Phase library under them. Search by name, brand or active.
Select your product, or Use beside a library product. For a product in neither list, type its name and select Use “…” as typed. Until a product is chosen the rates count in kg/ha. Then, while no zone has a rate, the unit follows the product: lime starts in t/ha.
Under 2 · Rate unit, check the unit: kg/ha, t/ha, L/ha, mL/ha, g/ha, units/ha or seeds/ha. One unit covers the whole map.
To change the zones, select Change zones in the This zone map panel.
Give every zone a rate
Under 3 · Rates, type the rate for zone 1 and for the top zone, then select Fill. Phase steps the zones between evenly. For one flat rate, type it in the first box and select Or put … on every zone.
Change any zone by typing in its box.
For a zone the machine should drive but put nothing on, select Skip (rate
0). Select it again to clear it.Check Product needed (what to order) and Average rate under the zones. The step bar shows the total product too, and what is still missing, such as "3 of 5 zones need a rate".
Don't leave a no-apply zone blank: most controllers read a blank as zero or use the display's own rate.
Count rates in units of N, P, K or S
When Phase knows the product's analysis, a Count rates in row offers product in your unit (for example Product (kg/ha)) and up to five nutrients the product carries, such as Units of N or Units of K.
Select the nutrient.
Type each zone's rate in kg of that nutrient per hectare, by hand or with Fill. Each zone shows the product rate that supplies it, and the foot shows the nutrient total beside the product to order.
The file always carries product rates. Nutrient entry needs a unit in kg, g, t, L or mL per hectare. A liquid whose analysis doesn't match the unit (such as weight-for-weight, rated in L/ha) needs its density on the product; the screen says so. A new product or a reopened map starts counting in product again.
A potassium (K) prescription. Build the zones from the soil layer showing Colwell K, with Low readings on top (see Build and edit a zone map). On Prescription, choose your potash product, select Units of K, rate every zone in kg K/ha (0 to skip) and export a Shapefile.
Export the prescription file
Select Export on the step bar, or Actions → Export in the header. On a phone, the Tools tab also has Export zones or Rx.
In the Export window, check What are you exporting reads Prescription (Rx). With a rate on every zone the window opens on it; until then only Zone map (zones only, no rates) can be chosen.
Under File format, select Shapefile (.zip), which machinery reads, including John Deere displays. GeoJSON is for mapping software and your agronomist; controllers don't read it.
Read the note under the choices. It names the rate column to pick on the display and its unit, such as "Select KG_HA as the rate column in your controller, in kg/ha."
Select Export prescription. On a computer the file downloads. In the Phase app on a phone or iPad, choose where to save it.
Load it with the controller's own import steps, choosing that rate column and unit.
On the display, check the product, rate column, unit, paddock and every zone. Set the out-of-zone and no-GPS rates: any gap between zones is applied at those rates, not at zero.
What the file holds. One row per zone with the rate, UNIT, PRODUCT, paddock (FIELD) and hectares. The rate column is named for its unit: KG_HA for solids, L_HA for liquids, SEEDS_HA for seed or UNITS_HA for units. Displays rarely offer t/ha, so t/ha and g/ha are written as kg/ha, and mL/ha as L/ha: lime at 2.5 t/ha arrives as 2500. ISOXML and John Deere Rx files aren't available yet.
Send the average rate to Crop Plan Studio
Starting from the plan. In Crop Plan Studio (the Plan page), select ••• beside a product line on a spray, spread, seeding or application pass, then Vary by zone in Spatial… (pick the paddock if the pass covers several). Spatial opens on that paddock's Zones step. Choose the product and rates yourself.
Writing the average back:
On the Prescription step, select Use in crop plan (under the zones' rates, beside Save version). The window shows the Average rate, the Total over the rated area, and the product lines on this season's passes for this paddock that aren't done yet.
Tap the line to update (a single line is already chosen), then select Update plan line. Phase writes the area-weighted average to the line in the line's own unit, and its cost follows. The line shows VR avg.
To take it back, select Undo average update in the same window.
The zones stay in Spatial; the crop plan carries only the average.
Save and reopen a prescription
Select Save version under the zones' rates, or Save in the header. On a phone, Actions → Save zone map also works.
The first time, type a Zone map name and select Save. Phase says "Saved version 1". Each later save adds a version and leaves earlier ones as they were.
A version keeps the zones, painted changes, product and rates. To reopen one, find it under Zone maps on the Layers step (on a phone, the Zone maps tab), open its ••• and select Edit zone map. It opens on the Zones step exactly as saved, rates included, and rebuilds only if you change a setting. The same menu has Rename and Delete zone map (see Build and edit a zone map).
Apply the setup to other paddocks
On the Prescription step, select Apply to other paddocks.
Untick any paddocks you don't want. Only paddocks with the layers this map needs are ticked. The rest sit under a fold such as "3 paddocks can’t take this map", with the reason (no mapped boundary, or no matching layer for the same dates and crop).
Leave Uniform product rate blank for zone maps only, or type one rate (kg/ha, t/ha or L/ha) of this map's product for every zone. This map's zone rates are never copied, because zone numbers mean different ground on each paddock.
Tick Save a zone map on each paddock to keep the results.
Select Build N zone maps. Each paddock shows Built, Skipped or Failed, with the reason.
For one file, select Export N together. The format starts on Shapefile (.zip), the format machinery reads.
Each paddock gets the same layers, filters, zone count, method, cut points and clean-up, worked out from its own data, so check each one. To give a paddock its own rates, reopen its saved map with Edit zone map. In a combined file the FIELD column separates paddocks; check your controller can filter by it. A paddock in the run with no rates stops the export and is named, rather than being written in with blank rates.
From a soil-type map. Every other paddock the soil map covers gets one zone per soil from its own soils. Instead of a uniform rate, the window asks for a rate per soil type, filled in from this paddock ("Not on this paddock" marks the rest), and each paddock's zones take their soil's rate by name. A soil left blank gets no rate.
Good to know
Phase Agent sets a zone's rate only when you give it the number. Check every value it sets.
Changing the unit after typing rates keeps the numbers as typed; they aren't converted. Check every zone again.
If you rebuild the zones and they come out different, Phase clears the rates and says so.
Zones are trimmed to the paddock boundary. Ground cut out of the boundary, like a dam, gets no zone and no rate.
If something doesn't look right
Prescription (Rx) can't be chosen in the Export window. Every zone needs a rate in one unit,
0for no-apply. The window shows how many are priced, for example "3 of 5 priced", and the step bar says how many zones still need a rate.The file has no rates. It went out as a Zone map. Export again with Prescription (Rx).
The controller won't open the file. Export a Shapefile, not GeoJSON.
There's no RATE column. The rate column is named for its unit, such as KG_HA. The read-me in the zip names it.
Lime shows in the thousands. t/ha is written as kg/ha. Choose kg/ha on the display.
Count rates in is missing or greyed out. Phase has no analysis for the product, or the unit is seeds/ha or units/ha.
Use in crop plan is missing or empty. It needs at least one rated zone in one unit, and a pass with products on this paddock that isn't done yet. Add the pass in Crop Plan Studio first.
"The plan line could not be updated." The map's unit can't be turned into the line's, for example kg/ha into L/ha. Choose a line measured the same way (by weight or by volume).