Skip to main content

Set rates by units of N, plants per m² or a season target

Enter a fertiliser rate as units of nitrogen, a seed rate as plants per square metre, or plan to a season target.

P
Written by Phase Team

Crop Plan Studio (the Plan page) and a paddock's Plan tab have three calculators built into the pass cards. You can type a fertiliser rate as units of nitrogen (or another nutrient) and let Phase work out the product rate, work out a seed rate from the plants per square metre you want, or bring a crop's whole season up to a nitrogen target. They work as you type.

Before you start

  • Open Crop Plan Studio. On a computer, select Plan in the top navigation. On a phone, select More → Paddocks & crops → Crop Plan Studio.

  • You need permission to edit crop plans to change rates. Anyone who can view the plan sees the figures.

  • Phase works nutrients out from each product's analysis, from your Inventory or the Phase Library. A product with no analysis can't be calculated.

Enter a fertiliser rate as units of N

Under every fertiliser line, in Add a pass and on the pass cards, a second row shows what the rate puts on, for example "= 46 N units/ha" for 100 kg/ha of urea.

  1. Open the pass and find the fertiliser line.

  2. To work forwards, change the product rate. The units row updates as you type.

  3. To work backwards, type the units you want into the units row, for example 60. The product rate changes to match.

  4. For a blend that carries more than one nutrient, pick which nutrient you're typing (N, P, K, S and so on) from the list beside the box.

  5. Press Save under the line, or Save changes at the foot of the pass.

The row also shows the other nutrients the product carries, and the total product and total cost over the paddocks you have selected.

The rate Phase lands on is rounded to one you'd write down. The units shown afterwards are what that rounded rate actually gives, so the two always agree.

Liquid fertilisers: weight or volume

A liquid's analysis only means something once Phase knows whether the label states it by weight (% w/w) or by volume (% w/v), and how dense it is.

Why the supplier says 42.2% and Phase says 32%. Both can be right for the same drum. A UAN liquid is 32% N by weight (w/w), which is about 42.2% N by volume (w/v) at 1.32 kg/L. Don't type 42.2 over a w/w analysis: Phase would then overstate the nitrogen.

To set it:

  1. Open Inventory → Fertiliser and open the product.

  2. Choose Edit.

  3. Under Liquid: how the label states it, set Analysis is to % w/w: kg in every 100 kg or % w/v: kg in every 100 L, to match the label.

  4. For a w/w analysis, enter the Density (kg/L), for example 1.32.

  5. Check the figures under Nutrient analysis (%) match the label, then save.

How Phase works it out for a rate in L/ha:

  • w/w: Phase turns the litres into kilograms with the density first. A UAN liquid at 30 L/ha, 32% N w/w and 1.32 kg/L puts on about 12.7 kg N/ha, not 9.6.

  • w/v: litres × the percentage.

  • Solids are worked out as before.

The Phase Library already records the basis and density for UAN liquids and similar products, and your copy follows it unless you've changed the analysis. Until the fields are filled in, the line says Phase has assumed w/v rather than guessing quietly. A w/w liquid with no density isn't calculated at all, and the line asks for the density.

Work out a seed rate from plants per m²

The seed line on a seeding activity has a Work out from plants/m² row. It shows when the seed rate is in kg/ha.

  1. Open the seeding activity and tap Work out from plants/m² under the seed line. Once the figures are in, the row shows the result instead, for example "≈ 160 plants/m²". Tap that to change them.

  2. Pick the Seed lot if it's in Inventory with its thousand grain weight and germination recorded. They fill in. Or leave it on No lot chosen: enter the figures and type them yourself.

  3. Enter or check TGW g (thousand grain weight) and Germ % from the seed test.

  4. Enter Establish %, the establishment you expect for this paddock and seeder.

  5. Read the plants/m² your kg/ha stands for. Or type the Plants/m² you want and the kg/ha follows.

  6. Press Save under the line, or Save changes.

Pick a heavier seed lot and the same plant density becomes a higher rate. Phase supplies none of these numbers itself, and each one is labelled with where it came from.

Bring the season up to a nutrient target

Every paddock starts somewhere different. A season target works each paddock out on its own.

  1. Select the crop's paddocks in Crop Plan Studio.

  2. Tap Nutrients, directly under the crop line. It shows kg/ha applied of planned, and which passes carry them.

  3. Choose Set a season target….

  4. Under What to do, choose Bring the season up to, Add or Take off.

  5. Type the Amount in kg/ha and pick the Nutrient. For example, bring the season up to 100 kg/ha of N.

  6. Under Carried by, tick the planned pass that should carry the change. The latest pass that carries it is ticked first, usually the last top-dress. Tick more than one and the change is shared between them in the proportion they carry the nutrient now.

  7. Choose Round new rates to a sensible figure, the nearest 5 or the nearest 10.

  8. Read the table. For each paddock it shows Applied so far, Planned, the Change, where that leaves the Season, and the new product Rate.

  9. Choose Show what else this changes to see the knock-on effect on product, cost and stock before you apply.

  10. Press Change N paddocks.

It applies as one change with one Undo.

Paddocks that can't take the change are listed with the reason rather than skipped quietly. For example: already above the target, no planned pass chosen to carry the nutrient, no nutrient analysis for the product, or a product that can't give up enough to take that much off. The season total shown is what the rounded rate really delivers.

Good to know

  • The same sums everywhere. Nutrient figures in the Studio, the Compare table and the season plan PDF all come from the same arithmetic, so they agree with these rows.

  • Applied means done. Applied counts passes recorded as done. Planned is what's still to go on.

  • Phase does the arithmetic. The target is yours. It doesn't recommend a rate.

  • On both doors. The units row, Work out from plants/m² and Set a season target… work the same on a paddock's Plan tab, which shows the same pass cards and Nutrients line as the Studio.

If something doesn't look right

  • A product shows the wrong kg/ha of a nutrient (for example lime sand with far too much calcium). The figure comes from the product's analysis. Open Inventory → the product's section → the product → Edit → Nutrient analysis (%), and correct the percentages. Watch for a value 10 times too high or low. For a liquid, also set Analysis is and Density (kg/L). Plans recalculate from the product.

  • No units row under a fertiliser. The product has no nutrient analysis, or the rate unit can't be converted (nutrients are worked out from a rate per hectare in kg, g, t, L or mL).

  • The line says the analysis is "read as % w/v". Nobody has recorded whether the label is w/w or w/v. Set Analysis is on the product.

  • The line asks for the density. The analysis is w/w and the rate is in litres, or the other way round. Enter Density (kg/L) on the product.

  • There's no Set a season target… button. It's inside Nutrients, under the crop line: tap it to open it. If it still isn't there, none of the selected paddocks has a planned fertiliser Phase has an analysis for, or you can't edit the plan. Add the fertiliser pass first, or record the product's analysis in Inventory.

  • No Work out from plants/m² row. The seed rate isn't in kg/ha. If you can only view the plan, the row shows only once someone has entered the figures.

Related

Did this answer your question?