Build a zone map in Phase Spatial from one or more layers, such as a yield map, a soil test or NDVI, choose how many zones, then paint by hand any corner the data gets wrong. The zone map is what you give rates to for a variable-rate prescription.
Before you start
Phase Spatial comes with Phase Ultra and the free trial.
The paddock needs a mapped boundary and at least one layer: a saved yield map with three or more usable cells, or soil results with three or more numeric readings from located sites. See Bring data into Phase Spatial.
Build a zone map
Open More → Paddocks & crops → Spatial.
Tap the paddock on the farm map, or choose it in the picker at the top.
On the Layers step, switch on the layer to build from.
Select Build zones on the step bar along the foot of the map (on a phone, just above the tabs). Create zone map does the same. On a computer it shows under Zone maps when the paddock has no saved map yet; on a phone it is always there. The Zones step opens with the layer you had on already chosen, and Phase builds the map straight away.
Under Build zones from, each layer in use is listed first; the rest are under Add another layer. Select Add on a layer to blend it in, and Remove on one in use to take it off. Two or more blend together.
On the step bar, set How many zones: 2 to 10 as buttons on a computer, or − and + on a phone (2 to 12). Each zone's hectares show beside it.
Open Adjust this layer and check the Top zone: High readings on top or Low readings on top.
With two or more layers, set each layer's Influence: how much of the map it decides. A layer on its own has no slider, because it counts for the whole map.
Check the zones on the map and in the zone list: each zone's range of readings, its hectares, small patches and any unzoned ground.
When the zones look right, select Set rates on the step bar. See Set rates and export a prescription.
Which readings make the top zone. The top zone is the last, highest-numbered zone, and a quick fill on the Prescription step gives it the highest rate. Lime on pH puts low readings on top; nitrogen on yield puts high readings on top. A soil measurement starts with a sensible choice (low on top for pH, N, P, K and sulfur; high on top for organic carbon, PBI, EC, CEC and aluminium), but always check it.
A potassium (K) map. Switch on the soil layer and choose Colwell K under Measurement (add yield or NDVI if you like). Build the zones, set How many zones, and check Low readings on top, so the lowest K gets the most product.
Adjust this layer also holds Leave out readings, to ignore headland zeros and impossible spikes below or above a value, and Depth from (cm) and Depth to (cm) where the data has depths.
Make zones from a soil-type map
A soil-type or zone map that names its zones (Sand, Loam, Mallee) already says where each soil is, so the zones can be those soils.
On the Layers step, switch on the soil-type layer.
Under its colours, select Make zones from these. Phase makes one zone for each soil type on the paddock, named for it, exactly where the map drew it: no smoothing, and every patch kept.
Select Set rates. The rates step asks for a rate for each soil type by name.
The exported file names each zone (ZONE_NAME "Loam") with its rate, and a saved map keeps the names. Changing the zone count or a cut point, or turning on smoothing, turns the zones back into Zone 1, 2, 3, so a soil name can never sit on the wrong ground.
Fine-tune the zones
Everything else is folded under Fine-tune the zones, with the current settings written on the fold, such as "Equal area · medium smoothing · patches under 1 ha merged". On a computer it's under the zones in the column beside the map; on a phone it's in the Tools tab.
How zones are cut:
Equal area (the default): each zone covers about the same area.
Natural breaks: cuts where the readings themselves step.
Equal steps: even steps from lowest to highest.
Custom: you type the cut points.
Custom cut points. With one layer they're in that layer's units, such as pH. With several blended layers they're on a combined 0–1 score. Use one layer with Custom when the job needs real boundaries, such as pH 5.2 and 5.8.
Smoothing (Off, Light, Medium, Strong) blends the surface before it's cut, so boundaries follow the ground rather than noise. Check how it changes small patches and edges.
Smallest zone (Keep all, 0.5, 1, 2 or 5 ha) merges smaller patches into the country around them. A spreader needs 20 to 30 m to change rate, so a patch it crosses in a second gets the wrong rate anyway.
More settings holds Cell detail (Layer, the same 8 m grid as the Layers step, or 10, 20 or 30 m), Tramline direction (a bearing from north; turn it until the cell rows follow your A–B line) and Match the layer: Match visible layer reuses a layer's colour bands as the zones (switch on and select exactly one layer, with its smoothing Off).
Zones are relative: zone 1 is the bottom zone and the highest number is the top zone. The order isn't an agronomic recommendation.
Paint corrections by hand
Set the layers, top zone, depth, zone count and fine-tune settings first. Rebuilding the map, which any of those changes do, clears your painted changes. Reopening a saved map doesn't: it opens as you saved it.
The brush sits on the map's tool bar on the Zones step, on a computer and on a phone:
Select Paint. The zone swatches and the Brush size come up on the map. On a phone the panel closes so they're in reach.
Pick the zone to paint from the swatches, and set the Brush size.
Drag over the cells to give them that zone.
Erase leaves an area unassigned. Move moves around the map. The undo and redo arrows beside them step through your strokes. On a phone, Reset edits in the Tools tab clears every stroke at once.
Check areas and totals yourself before ordering or applying product.
Save the zone map
Select Save in the header. On a phone, select Actions → Save zone map, or Save version in the Tools tab.
Type a Zone map name.
Select Save. Phase says "Saved version 1". Saving again adds a version to the same map rather than starting another.
Saved maps are listed under Zone maps on the Layers step (on a phone, the Zone maps tab).
Reopen, rename or delete a saved map
Open the map's ••• menu (the three dots on its row):
Show on map shows it over the paddock.
Edit zone map reopens it on the Zones step exactly as you saved it, painted corrections and rates included. It rebuilds only when you change a setting: a layer, its influence, the zone count, a cut point or the smoothing.
Rename opens Rename zone map: type the Zone map name and select Rename.
Delete zone map asks first, then takes the map off the paddock's list. Files already exported from it, and jobs that used it, are not affected.
Good to know
Zones cover the whole paddock. A dam or scrub cut out of the boundary gets no zone and no rate, and is left out of the hectares, totals and exported file. A piece across a road or creek is zoned with the rest.
Each zone covers only its own ground, so two zones never overlap in an exported file.
If the zones change after you've set rates, Phase clears the rates and says "Zone geometry changed; previous product rates were cleared." Reopening a saved map with Edit zone map keeps its rates.
Unzoned ground ("ha unzoned: no data covers it") is outside the reach of the data. It isn't a zero rate.
Colour choices are saved with the zone map, and Save and Export wait until the map has finished building.
Re-export any prescription made before October 2026 for a paddock with a dam cut out or a piece across a road. Older files could rate the dam, leave out the far piece, or overlap two zones.
Phase doesn't choose agronomic rates or replace professional advice.
If something doesn't look right
No zones appear. Read the step bar first: it says what the map is waiting for. Then check a layer is selected, at least one Influence is above zero, depth or Leave out readings hasn't excluded every reading, and the boundary is valid. "The zones could not be built" means try the layer again or another one.
Soil pH or another soil measurement isn't offered. The paddock needs at least three numeric readings for it that year, from sites with a location.
Soil results "can't be mapped yet". Those sites have no location. Select Link results to zones, or import the results with coordinates.
No paddocks appear. Add or fix a boundary with at least three points in More → Paddocks & crops → Farms & Fields.
The agent says there's no data. Switch the layer on in the Layers step and ask again.
A saved map won't reopen and says the boundary has changed. The zones no longer line up with the ground, often on a paddock in pieces or with a cut-out. Build a new map from the same settings.
"That map was saved before Phase kept an editable copy". Show it on the map to look at it, or build a new version from the same settings.
Export is refused. For a plain zone map, clear every rate. For a prescription, give every zone a rate of 0 or more, all in the same unit. Use 0 for a zone that gets nothing.
A save or build problem. Open More → Help chat with the farm, paddock, zone map name, the exact error and a screenshot.