Skip to main content

Set up a spray: nozzles, droplet size and Fill Assist

Save spray nozzles, set the droplet size, understand the 2,4-D droplet warning, and use Fill Assist to plan tank loads and mixing order.

P
Written by Phase Team

This article covers the spray details on a crop plan: saving the nozzle you run, the warning Phase shows for 2,4-D and droplet size, and Fill Assist, Phase's tank-mix tool that works out how much water and product go in each tank load and in what order.

The quick answers. Yes, Phase has a tank-mix tool: it's Fill assist, the button on the Water row of an open spray, in Crop Plan Studio and on the paddock's Plan tab. And there's no nozzle list to keep: type the nozzle on a spray once and Phase offers it next time.

Add a nozzle to a spray

An open spray pass has a Nozzle row beside Droplet, under the water rate. It works the same in Crop Plan Studio and on a paddock's Plan tab.

  1. Open the spray pass: in Crop Plan Studio, select the paddocks and tap the pass; on the map, tap the paddock, then Plan, then the pass.

  2. Tap Nozzle (it says Add when there is none yet).

  3. Type the nozzle under Nozzle, for example air induction 11003, or pick one Phase suggests.

  4. Choose the size under Nozzle size (ISO colour).

  5. Select Save changes.

When you add a new spray with Add, the nozzle size and nozzle are on its details step, in Crop Plan Studio and on the Plan tab. On a pass already planned, tap the nozzle in the water band.

Phase remembers every nozzle used on the farm, on a plan or a finished spray, and offers them as suggestions. There is no separate nozzle list to maintain. The same suggestions show in Crop Plan Studio, on a paddock's Plan tab and in John Deere Reconcile.

The coloured size chip shows on the activity and on the finished spray record. Marking a planned spray done carries its nozzle into the finished record, and onto the Spray Records report.

Nozzle sizes and colours. The sizes use the colour code operators know:

Size

Colour

01

Orange

015

Green

02

Yellow

025

Lilac

03

Blue

04

Red

05

Brown

06

Grey

08

White

Nozzle names typed before the size picker existed are read for their size where possible. A name ending in 11002, for example, is recognised as size 02 and shows with that size's chip.

In Reconcile. For a John Deere spray, the reviewed Deere value, or a nozzle you type over it, takes priority over the planned one. If the plan's nozzle is the right one, select Plan beside Nozzle to put it back.

Set the droplet size

On an open spray pass, tap Droplet beside Nozzle and pick the size from the list, then select Save changes. This is the same in Crop Plan Studio and on a paddock's Plan tab.

When you add a spray with Add, the details step asks the droplet size, one of six: Very fine, Fine, Medium, Coarse, Very coarse and Ultra coarse. On a pass already planned, tap the droplet in the water band to change it.

The 2,4-D droplet warning

If a spray contains 2,4-D and its droplet size is not set, or is finer than very coarse, Phase shows a label warning. It says, for example, that the product "contains 2,4-D — the label requires a VERY COARSE or larger droplet, and this spray has no droplet size set."

  • The warning shows on the spray's card, under its name, in Crop Plan Studio and on a paddock's Plan tab.

Phase looks for 2,4-D in the product's name and in the linked product's active ingredients. A product whose active ingredients aren't known can't be checked, so no warning is not a sign the spray is compliant.

The warning clears once Droplet size is set to very coarse or coarser. Check the label for the droplet size your product needs.

This is a reminder, not a block and not a certification. Check the current product label, any permits, the conditions and your agronomist's advice before spraying. The product label is always the authority.

Work out a tank fill with Fill Assist

Fill Assist is a tank-fill guide for a planned spray. It uses the products and rates already on the spray, so you only enter the tank size and how much you're filling for.

  1. Open the spray pass, in Crop Plan Studio or on the paddock's Plan tab (Map → the paddock → Plan).

  2. Select Fill assist, on the Water row of the pass.

  3. Under Calculate by, choose Full tank, or Set area to fill for a set number of hectares.

  4. Set the Tank capacity in litres. Tap a preset (4,000, 5,000, 6,000 or 8,000 L) or type it. Phase remembers it on that device.

  5. Check the Water rate. It is loaded from the plan. A change here is for this fill only and doesn't change the plan; Use plan rate puts it back.

  6. With Set area, enter the Area for this fill in hectares. The Load estimate shows how many hectares the fill covers and how much water it takes.

  7. Select Review mix order.

  8. Read The label is the authority, then select I understand once you have read the product labels.

  9. Check the suggested order under Check the mixing order. Use the arrows to move products earlier or later to match the labels.

  10. Select Start fill guide and follow it one step at a time: water first, at least half the tank, then each product with its amount, then the final top-up. Select Water added, Product added and Complete fill as you go.

How the order is suggested. Phase suggests a general order from each product's formulation type:

  • First, water conditioners.

  • Then wettable powders and water-dispersible granules, then dry flowables and soluble granules.

  • Then suspensions, emulsifiable concentrates, water-soluble liquids and oil dispersions, in that order.

  • Then adjuvants and crop oils.

  • Liquid UAN, if the mix has it, goes in last of all.

It isn't label advice and it doesn't check whether the products can be mixed. The label and your agronomist always come first. Jar-test a mix you're unsure of.

Leaving part way. If you close Fill Assist during the fill guide, it asks Leave this fill? Select Keep filling to carry on, or Leave to close. Nothing is recorded either way.

Rates per 100 L of spray mix

A rate per 100 L of spray mix (L/100L, mL/100L, g/100L or kg/100L) is worked out from the water rate. For example, 200 mL/100L at 80 L/ha is 160 mL/ha.

Fill Assist, the plan's $/ha and the stock taken off on Mark done all use that worked-out figure. Before 9 October 2026 they treated it as per hectare.

Good to know

  • Fill Assist only calculates. It does not record the spray, take stock out of Inventory or check that the products are compatible. Mark the spray done as usual once the work is finished: see Mark work as done.

  • Fill assist is on every open spray pass, in Crop Plan Studio and on a paddock's Plan tab. Since 7 November 2026 it sits on the Water row, not under the products.

  • A product with a zero rate is skipped, and Fill Assist says so.

If something doesn't look right

  • Fill Assist says "Set a water rate above to calculate this fill." Enter a Water rate, or add one to the spray: tap Water on the pass, then Save changes.

  • Fill Assist says it "needs at least one product with a positive per-hectare rate". Add a product with a rate to the spray first.

  • The area for this fill is more than the tank. Phase says the water needed is more than the tank holds. Lower the area or the water rate.

  • My nozzle isn't in the suggestions. Type it once on a spray and save. It is offered from then on.

  • The 2,4-D warning is showing. Check the droplet size against the label, as above. If the droplet size is already very coarse or larger and the warning still shows, contact Phase support.

Related

Did this answer your question?