Reconcile is where completed John Deere work waits for you to check it before it becomes a record in Phase. This article covers how new work arrives each morning, finding your way around the queue, and reading a job before you confirm it. CNH FieldOps harvests wait on their own page, Work reconcile → CNH FieldOps: see CNH FieldOps: import paddocks and engine hours.
Before you start
Your farm needs Phase Ultra or the free trial. On Phase Pro, Reconcile shows Unlock John Deere Work Sync with Upgrade to Ultra on a computer, or Reconcile on this device with Retry in the phone app.
John Deere must be connected to the right organisation. See John Deere Operations Center.
Open Reconcile from More → Daily work → Work reconcile → John Deere, on a computer or a phone, or from the Work queue tile on Overview. It was a tab in Inventory until October 2026.
How new work gets into Reconcile
Most work arrives without you pressing anything. Each night, from about midnight Perth time, Phase checks Operations Center for every connected farm on Phase Ultra or a free trial. New completed jobs from the current season are waiting in the morning.
Their products are already matched to your inventory, the same way Refresh matches them. Phase has also asked John Deere for each new job's diesel and maps, and for a harvest matched to a paddock it has started John Deere building the yield map.
The Checked … note beside the heading says when the queue was last checked. On a computer, point at it to see when the overnight check ran and how many new jobs it brought.
The overnight check never changes a job you have confirmed or ignored, and keeps your edits on a job still waiting. If someone saves a job while the check is updating it, their save wins and the update waits for the next night. Once a trial ends or a subscription stops, Phase stops pulling that farm's work.
Pull in work done today
Open More → Daily work → Work reconcile → John Deere.
Check the season selector is on the season the work was done in.
Select Refresh. Phase pulls new completed work and rebuilds the unconfirmed jobs in that season. Edits you already made stay with their products.
A job that takes more than a day
A machine can be on one paddock for days, and a week or more at harvest. Phase keeps that as one job. When John Deere adds to a job, Phase updates the job already waiting. When John Deere starts a second job for the same paddock, the same kind of work and the same mix within a week (a fortnight for harvest), Phase combines the two. Refresh does the same.
The job then says, for example, "John Deere added to this job (31.2 → 58.6 ha). It may not be finished", and asks you to wait until it stops changing before you confirm. Confirm ready jobs leaves it unticked, with "John Deere is still adding to it. Wait until it is finished", until it has gone two days without changing. You can still confirm it by hand. A job that grew has its diesel read again, so the figure covers the whole job.
Find your way around the queue
The heading reads Imported work with the season and a count such as 12 waiting. The Data Feeds link at the top goes back.
Season. A job appears in the season its work dates fall in, and a job with no date always shows. To see older work, switch season.
Status headings. Every job is on the page under one of these, and the counts along the top jump to each: Ready (matched to a paddock and plan), Review (something differs from the plan), Unmatched (no paddock or plan yet), Confirmed and Ignored.
Search and Filters. Search by paddock, product or activity, or use Filters for one farm, paddock, kind of work or date range.
Each row shows the paddock, kind of work, date, area worked against the paddock's area, the plan activity it matched (or No plan matched), the John Deere mix name and the machine.
On a wide computer screen the list is a narrow column on the left and the selected job opens beside it. On a phone, tablet or narrower window, a job opens as a panel over the list. Scroll the panel to reach every product; the confirm button is at the bottom.
Re-match or clear the queue
The ••• menu beside Refresh holds:
Change JD org: pull work from a different John Deere organisation.
Re-match queue: check the selected season's waiting jobs again against your paddocks, crop plans, products and storage, for example after adding a plan. Confirmed and ignored jobs are not changed.
Clear pending work (all seasons): remove every waiting John Deere job from every season, not only the one shown. Phase asks first; select Clear pending work to go ahead. Confirmed and ignored jobs, and anything already posted to paddocks, stock or crop plans, stay as they are.
Read a job receipt
The top of a job shows the paddock name (or Match a paddock when it has none), then the John Deere Mix name and the date. With no mix name from John Deere, it shows the Plan name or Job type instead. Underneath:
Total spray rate (sprays): the whole-mix volume in L/ha the sprayer measured, or John Deere's total divided by the area treated. The caption says From John Deere, From Deere total ÷ area or Edited by you.
Area worked (Area harvested on a harvest), marked Deere reported or Area edited. Edit paddock / area changes the paddock or the area.
Linked Phase plan: the planned activity this work completes. Change plan picks another, or records the work as its own activity without a plan.
The Paddock and Plan steps open whenever either needs a decision. Below them are the products (or a Harvest panel), the job's maps, Related Deere jobs when there are passes to combine, and More details for the operator, spray details, weather, notes and machine.
Work recorded on a paddock with no plan for the season is kept for that paddock, and the paddock's first Crop Plan Studio plan for the season takes it in.
Enter a spray rate John Deere didn't report
If John Deere didn't measure the spray volume, or its readings disagree, Total spray rate shows Not reported and Actual rate not reported.
Select the pencil beside Total spray rate.
Enter the Actual total spray rate · L/ha, the whole mix including water.
Select Save spray rate.
Reset to Deere puts John Deere's figure back. The planned water rate is shown for reference but never used as the actual. Jobs you combined by hand may need the rate entered this way.
Change a job from spray to spread, or back
Phase decides the type from the product names John Deere sends:
A job from the sprayer is a spray, even with ammonium sulphate (AMS), UAN or a trace-element blend in the tank.
A liquid product with a brand name and no fertiliser word in it, such as a liquid trace element or a biological, comes in as a spray.
A fertiliser on its own, such as urea, MAP or UAN by itself, comes in as a spread.
A dry product that isn't a fertiliser, such as bait, can come in as a spray.
To change it:
Open the job and select Change plan.
Pick the Activity type: Spray, Spread, Seed, Apply, Harvest, Tillage or Operation.
Check Matched plan activity still points to the right pass, or choose Actual only (no plan activity).
Changing the Phase product on a line doesn't change the job's type.
Good to know
Before 21 October 2026, any product with a fertiliser-sounding name made the whole job a spread. Waiting jobs were corrected at the next sync covering their dates. Confirmed, ignored, merged and grouped jobs were left as they were, so check their type before confirming.
Since then, sprays also show the water rate John Deere recorded as their Total spray rate. Most used to show none.
Nothing in Reconcile changes your records until you confirm a job.
If something doesn't look right
Today's work isn't there. Press Refresh. A job still being worked comes in marked as possibly unfinished.
Older work is missing. Switch the season selector to the season the work was done in.
I only see a few jobs. Look under Review and Unmatched as well as Ready.
The work is in another John Deere organisation. Use ••• → Change JD org.
"Wait for the John Deere refresh or re-match to finish before confirming work." Wait for it to finish.
Reconcile shows an error. Read what it says, because each reason has its own message:
John Deere has paused the organisation until someone accepts its updated terms: the message links to John Deere's terms page. Accept them, then try again. Reconnecting won't help.
John Deere is busy or its servers are having trouble: nothing is wrong with your connection, and the message says when to try again.
Phase isn't licensed for that part of John Deere's data: reconnecting won't change it. Contact support@phase.ag.
The person who connected Phase can't see this data in the organisation: an Operations Center admin can give them access in John Deere's Team Manager.
John Deere stopped accepting the sign-in, or the connection is missing access Phase asks for: use Reconnect Deere and approve what it asks for. For anything else, note the exact wording and take a screenshot, check the John Deere Operations Center page reads Connected, then try again. If it keeps happening, send the details to support@phase.ag.
Reconcile is locked although the farm is on Phase Ultra. Reload Phase. In the phone app, select Retry. If it is still locked, ask the farm account owner to check the subscription.
A product shows twice on a job. See Match John Deere products and clear a backlog.
