Check what is in each silo, shed and stack, set the right figure after a stocktake, fix grain loaded as the wrong variety, grade or season, and say which silo seed or feed came out of. Then print or export stock, contract and storage reports.
Seeding hasn't come off the silo? If the seed was in two or more silos and the job didn't say which, the use waits in Not taken out of a silo yet at the top of Yield Centre → Storage → Structures (and of Inventory → Grain & Hay). Choose the silo under Came out of… and tap Take it out.
Look through your structures
Open More → Paddocks & crops → Yield Centre → Storage (it opens on Structures), or Inventory → Grain & Hay. They show the same structures. Choose Cards or Map (pins on the satellite map).
In order, type by type. Inside each farm, structures are listed by type (grain silos, seed silos, field bins, grain sheds, hay sheds, hay stacks, bunkers and pads, seed sheds, then grain bags), with a heading and count over each type, such as "Grain silos 12". Inside a type they are in name order with numbers counted, so Silo 2 comes before Silo 10. Pick lists and the Stock on hand report follow the same order.
Search and filters. Once a farm has seven or more structures, a search box sits above them. Type part of a name ("silo 3" or "silo3"), what is in it ("barley" or "APW1") or a farm's name. The filters Type, Holding, Farm and Hide empty each turn on or off by themselves, with a tick when on. On a phone they sit behind one Filters button.
A line such as "Showing 12 of 77 structures" appears with Clear beside it. The filters apply to Cards and Map, stay on while you switch views, and clear when you leave the page.
What a card shows. How full the structure is as a bar and percentage, its first parcels, and labels: Sealed, Withholding, Over capacity, Gas-tight, Aeration and No pin. A striped drawing means stock but no capacity set. Open a structure to see each parcel, its fumigation state and recent activity, with Load in, Load out, Move, Fumigate, Check and Correct.
Quality by silo. Open a structure: under What's in it, each parcel shows its Quality, up to four figures (protein, moisture, screenings and test weight), each the average by tonnes over the loads that went in with that reading, with the lowest to highest load under it. When not every load had a reading it says so ("protein from 60 of 90 t"), and the latest storage check's moisture shows beside it ("checked 12.1% moisture 27 Oct"). Grain moved in from another silo brings that silo's averages; grain taken out leaves them as they are, because a silo blends. See more opens the latest check and every load that went in, with its readings. A structure holding more than one parcel shows the whole of it too, here and when you scan its Phase tag. Silo quality comes only from loads logged in Phase: CBH loads go to the receival site, so they show under By receival site on the Yield Centre's Loads → Delivered.
What's in storage at a glance. Stored on farm, in Where the harvest is on the Yield Centre's Overview, lists what is in your silos, sheds and stacks now, each one with what it holds, with Record load and Storage.
Say which silo seed or feed came out of
Completing a seeding takes the seed off stock. When the seed sits in one silo, that silo goes down. When it sits in two or more and the job didn't say which, the product's total goes down but no silo does. The same goes for anything else a job used from a silo, shed or stack without naming it. These uses wait in Not taken out of a silo yet at the top of Storage → Structures (and Inventory → Grain & Hay), which only shows when there is something to place. Each row has the amount, product, paddock and date.
Under Came out of…, choose the silo it came from. Each silo holding that product is listed with how much is in it. One holding less than the use says "(less than this)".
If the silo you chose held less than was used, a second choice appears for the rest. Choose the silo the rest came from. A line under the choices says what comes from where, such as "7.95 t from Silo 9 and 4.37 t from Silo 8."
Tap Take it out.
The first silo is emptied and the second goes down by the rest. Leave the second choice on "nowhere else" and it all comes off the first silo, which then reads empty until it is counted. The job's amount and the product's total don't change. The card shows three at a time; See all opens the rest.
Seeding recorded before 5 October 2026 from seed in several silos is in the list too. Nothing came off any silo for those until now, so check each silo's figure after placing them. Next time, choose the silo under Came out of when you mark the seeding done (see Mark work as done).
Feed. Since 17 October 2026, feed waits here less often:
Hay or grain kept in only one shed or silo comes out of it by itself, oldest first.
A ration can name its silos and sheds (see Rations and feed plans). When they hold less than the feed on paper, usually because a delivery was never recorded, the last listed silo holding that grain gives the rest. It reads empty until you count it with Correct or record the delivery with Load in.
Since 31 October 2026, a ration with no place set for a feed uses the place your other rations take it from, and keeps it.
If a feed still has nowhere to come out of when you record it, Phase asks first: Go back to pick the silo or shed, or Record anyway.
Only feed that none of the listed places holds, or feed kept in several places when nobody said which, waits here.
Feed already waiting stays in the list to be placed once with Take it out; new feed-outs place themselves.
Correct a stocktake
Open the structure and select Correct. In Inventory → Grain & Hay you can also select Actions → Correct and choose the Structure and Parcel. Phase shows what is recorded.
Type the Tonnes actually there. For hay, type the Bales actually there too. A line shows the difference against the record.
Check the Date and choose Why: Stocktake, Shrink / moisture loss, Spoiled or Miscounted.
Add Notes if you like, then select Save correction.
The correction is kept as its own record, so the history still shows what was loaded in and out. For hay you can save a change to the bale count even when the tonnes stay the same; the saved message and Activity show the bale change. Save correction only becomes available once the amount differs from the record.
Fix the variety, grade or season of a parcel
Open the structure.
Under What's in it, select Edit on the parcel (beside Correct).
Change the Variety, Grade (Quality for hay) or Season.
Select Save.
Every record in that grain's history is renamed to match, so past loads, moves and checks read the right variety. A corrected season also moves its loads to that season in Financial Performance and in the Yield Centre's grain value. The amount doesn't change. Loads already delivered keep the grade on their docket. If the structure already holds grain of the corrected variety, grade and season, the sheet says so, and saving joins the two into one parcel.
See totals and activity
These were Grain & Hay's Totals and Activity views. They are on the Yield Centre's Storage tab now, beside Structures.
By crop (was Totals) shows grain, seed, hay and silage on hand (silage on its own line, never in grain), structures in use, and each commodity by variety, grade and season with where it sits (Export CSV downloads it). Harvest by paddock shows what each paddock put into storage or delivered, for the season you choose.
Activity lists every load, move, fumigation, check and correction. Filter narrows it by Type (Loads in, Loads out, Moves, Fumigations, Checks, Corrections), Structure and Season. Each filter shows with an × to remove it.
Record a check, move grain or fumigate
Record a check, Move grain (Move hay for hay) and Fumigate are on each structure in Grain & Hay Storage and on a silo's Phase tag. Each opens as one card that asks one question at a time, like Load in. Optional fields sit behind More details, which opens right there in the card. In the Yield Centre, Record load → Between your structures moves grain too, and Actions → Fumigate records a fumigation. Inventory → Grain & Hay keeps all three in Actions.
Record a check.
Which grain are you checking? Tap the Silo and Parcel (skipped when you start from the silo).
What did it read? Type the Moisture and Grain temperature, and tap Insects: None seen, Live insects found or Not sieved. Under the moisture are what the grain went in at and the last check.
When was it checked? Set the day. More details holds a note (smell, crusting, hot spots).
Check the ticket and select Save.
Moisture over 30% or under 4% says "Check the reading", and over 55 °C asks "Is that °F?". Both can still be saved with Record anyway.
Move grain.
What are you moving? Tap the structure under Out of and the Parcel.
Where is it going? Tap the structure. Each shows what it holds and how full it is.
How much? Type the Tonnes (and Bales for hay). It shows what is in the parcel and what will be left. Move all of it fills in the whole parcel. You can't move more than is in the parcel.
When did it move? Set the day; More details holds a note.
Select Move it.
Moving more than the other structure holds, or into one holding a different grain ("Silo 3 holds Barley"), is flagged and the button reads Record anyway.
Fumigate.
Which are you sealing? Tap each structure sealed together. Any already sealed are marked.
What did you use? Tap the fumigant, or type it under Product. More details holds the dose.
When was it sealed? Set the day it was sealed, and the Opened and Clear to move from dates if you have them. Dates out of order can't be saved. More details holds who did it and a note.
Select Save.
A fumigated structure shows Sealed, then Withholding until its clear-to-move date. Mark opened on a sealed silo opens the same card at When was it opened?, with the sealed day and Clear to move from under it.
Print or export a report
Reports work with nothing in storage, for contracts and past records.
In the Yield Centre, select Actions → Storage reports. In Inventory → Grain & Hay, select Actions → Reports (shown once the farm has a structure).
Pick a report:
Stock on hand: each silo, shed and stack, what is in it, how full it is and its fumigation state.
Commodity summary: tonnes of each commodity, then by variety, grade and season, and where it sits.
Contract summary: each contract's sold, delivered, still to deliver, % delivered, $/t and delivered value, with a total, then Uncommitted grain.
Storage records: every load in, delivery, move, correction and check, oldest first.
Fumigation register: product, dose, sealed, opened, clear-from and operator.
Harvest by paddock: what each paddock put into storage or delivered straight off the paddock.
Choose a Season or All seasons (the fumigation register has no season choice). For contracts, choose Open contracts or All contracts, and tick List each delivery to add the deliveries with their dockets, moisture and protein.
Under Format, choose PDF (laid out like the Inventory report, with your farm name and the date), Excel (each table on its own sheet) or CSV (the tables one under another). A line shows how many rows each table will have.
Select Export PDF, Export Excel or Export CSV.
The spreadsheets carry extra columns the PDF leaves out, such as delivery from and by dates, delivery site, price basis, contract value, truck, temperature, insects and notes.
If something doesn't look right
Grain & Hay and Inventory → Seed show different figures for the same seed. They are one record and should match. Check Not taken out of a silo yet first. If the seed is in one place and the figures still differ, contact support.
Save correction stays greyed out. Type an amount that differs from the record. If it stays grey after that, contact support.
I can't find a structure. Select Clear beside "Showing … structures". Filters stay on until you leave the page.
I can't find Totals or Activity. They are Yield Centre → Storage → By crop and Activity since 29 October 2026.
I emptied a silo and it said "Could not save grain movement". Fixed on 28 October 2026. A Correct to 0 t, a Load out of everything left or a move of all of it now saves, and nothing was saved by the failed tries, so do it again.
I corrected a parcel's season, but Financial Performance still counts its sales in the old season. A parcel corrected before 27 October 2026 kept its loads in the old season there. Contact support with the silo and the parcel, and the team will move them.
Can I report on livestock contracts? No. Phase has no livestock contracts; Contract summary covers grain.