Skip to main content

Flex 22” Counter Stand Installation Guide

Follow the steps in this article to install your Flex 22" Counter Stand to your Flex 22 terminal.

Written by Agent Support Bot

Flex 22” Counter Stand Part Overview

This installation guide provides step-by-step instructions for installing the Toast Flex 22” Counter Stand. It covers both landscape and portrait mounting options, lists the tools and hardware included, and highlights essential safety precautions to help prevent injury or damage to equipment. Use this guide to ensure a smooth, secure installation of your Toast Flex 22" display stand.

Flex 22" counter stand part overview

  1. VESA plate

  2. Neck length set screws (x2)

  3. Lower hinge wire hole

  4. Base

  5. Base mounting hole screw covers

  6. Cable exits (x4)

Flex 22" counter stand part overview part 2

  1. Upper hinge

  2. Upper neck

  3. Lower neck

  4. Lower hinge set screw (x2)

Back to top

Flex 22” Counter Stand Installation Position

Note: Clear your installation area for your Flex 22” Counter Stand of any obstructions before you get started.

Below is how the Flex 22” Counter Stand will be positioned in the box.

Flex 22" counter stand image.

The bottom hinge has three positions: flat, mid, and vertical.

Flex 22" counter stand hinge positions.

Follow the steps below to the position for your Flex 22" Counter Stand:

  1. Unscrew the two Allen screws found on the face of the neck using the provided Allen key.
    ​
    ​

    Allen screws on the hinge of the Flex 22" counter stand.


    ​
    ​
    ​

  2. Adjust the lower neck hinge until the holes align.
    ​
    ​

    Adjusting the neck lower hinge of the Flex 22" counter stand.


    ​
    ​

  3. Screw the two Allen screws back on the face of the neck.
    ​
    ​

    Flex 22" - securing Allen screws to the neck of the hardware.

Back to top

Flex 22” Counter Stand Landscape Position

Follow the steps below to set the Flex 22” Counter Stand in the landscape position:

  1. Place the Flex 22” face down on a clean surface.
    ​
    ​

    Flex 22" device face down for landscape position.


    ​
    ​

  2. Position the stand VESA plate against the back of the Flex 22”.
    ​
    ​

    Position VESA stand against the back of the Flex 22".


    ​
    ​

  3. Using the 4 thumb screws that come with the Flex 22”, screw in the VESA plate to the back of the Flex 22”.
    ​
    ​

    Flex 22" counter stand attached to Flex 22".


    ​
    ​

  4. The power and Ethernet cable can now be run through the hole in the bottom of the stand.
    ​
    ​

    Run the Ethernet cord through the Flex 22" counter stand


    ​
    ​

  5. Connect to power and Ethernet according to the labels on the back of your Flex 22” terminal.

    1. Power and Ethernet Cables

    2. Grommet to seal the pocket

    3. Pocket for cable management

    4. Accessory pocket

    5. Grommet to seal the pocket

    6. Pocket for cable management
      ​
      ​

      Cord management for Flex 22" and Flex 22".


      ​
      ​

  6. Remove back panels. Open and remove the back panel from the top cut-outs to expose the back pockets.
    ​
    ​

    Flex 22" back panel removal to attach the Flexx 22 Counter Stand.


    ​
    ​

  7. Plug in your cables. Plug in the USB-C power and the (optional) Ethernet cable in the left pocket as shown.
    ​
    ​

    Flex 22" and Flex 22" Counter Stand cable alignment.


    ​
    ​

  8. Flip the stand onto its base and adjust the screen to your preference.
    ​
    ​

    Attach the Flex 22" Counter Stand base.

    Adjust the Flex 22" Counter Stand and adjust the screen.

Back to top

Flex 22” Counter Stand - Portrait Position

Follow the steps below to set the Flex 22” Counter Stand in the portrait position:

  1. Using the Allen tool provided, unscrew the two neck length adjustment screws on either side of the top of the neck.
    ​
    ​

    Portrait orientation for the Flex 22" Counter Stand.


    ​
    ​

  2. Pull the neck out until the second set of holes align. Note: Be careful not to pull the neck completely out.
    ​
    ​

    Align the Flex 22" base with the Flex 22" Counter Stand.


    ​
    ​

  3. Screw the two Allen screws on the face of the neck.
    ​
    ​

    Attach and screw the neck if the Flex 22" base in the the Flex 22" Counter Stand.


    ​
    ​

  4. Place the Flex 22” facedown on a clean surface.
    ​
    ​

    Flex 22" terminal face down for Flex 22" Counter Stand.


    ​
    ​

  5. Position the stand VESA plate against the back of the Flex 22”.
    ​
    ​

    Position the base of the Flex 22" Counter Stand to the base of the Flex 22".


    ​
    ​

  6. Using the 4 thumb screws that come with the Flex 22”, screw in the VESA plate to the back of the Flex 22”.
    ​
    ​

    Screw the base of the Flex 22" Counter Stand to the back of the Flex 22" terminal.


    ​
    ​

  7. The power and Ethernet cable can now be run through the hole in the bottom of the stand.
    ​
    ​

    Connect the Ethernet and power cables and run through the bottom of the Flex 22" Counter Stand.

  8. Connect to power and Ethernet according to the labels on the back of your Flex 22” terminal.
    ​

    1. Power and Ethernet Cables

    2. Grommet to seal the pocket

    3. Pocket for cable management

    4. Accessory pocket

    5. Grommet to seal the pocket

    6. Pocket for cable management
      ​
      ​

      Wire management for the Flex 22" terminal and installed Flex 22" Counter Stand.

  9. Remove back panels. Open and remove the back panel from the top cut-outs to expose the back pockets.
    ​
    ​

    Removal of the back panels of the Flex 22" terminal for the portrait install of the Flex 22" Counter Stand.


    ​
    ​

  10. Plug in your cables. Plug in the USB-C power and the (optional) Ethernet cable in the left pocket as shown.
    ​
    ​

    Cable management for USB-C power and Ethernet for the Flex 22".


    ​
    ​

  11. Unscrew the spring rotation thumbscrew on the back of the VESA plate.
    ​
    ​

    Flex 22" Counter Stand install to the Flex 22" terminal.


    ​
    ​

  12. Rotate the stand from landscape to portrait.
    ​
    ​

    Flex 22" Counter Stand install to the Flex 22" terminal.


    ​
    ​

  13. When aligned with the hole, push the thumbscrew in and tighten until the Flex 22” is locked in place.
    ​
    ​

    Secure the Flex 22" Counter Stand screw to the back of the Flex 22" terminal.


    ​
    ​

  14. Flip the screen onto its base and adjust the screen to your preference.
    ​
    ​

    Flip the Flex 22" terminal with the Flex 22" Counter Stand.

    Adjust the attached Flex 22" Counter Stand and Flex 22" terminal.

Back to top

Surface Mounting Method for Your Flex 22” Counter Stand

You are responsible for using appropriately sized mounting screws and mounting to the appropriate structural support if wall mounting.


You can select between two mounting methods for your Flex 22” Counter Stand: counter mounting and wall mounting.
​
​

Flex 22" Counter Stand - counter mounting

Flex 22" Counter Stand - wall mounting.


​
​
​

  1. Located the four covers on the stand base.
    ​
    ​

    Four mounting covers on the base of the Flex 22" Counter Stand.


    ​
    ​

  2. Position the stand onto the surface.
    ​
    ​

    Position Flex 22" Counter Stand on the surface position for mounting.


    ​
    ​

  3. Pull the covers. Note: Be careful, covers do not completely come off the base.
    ​
    ​

    Pull back screw covers to attach the counter or wall mounting.


    ​
    ​
    ​
    ​

  4. Life the covers to expose the mounting holes.
    ​
    ​

    Expose mounting holes for counter or wall mounting.


    ​
    ​

  5. Screw the stand to the surface (use the provided screws). Then, reinstall covers.
    ​
    ​

    4 screw mount for the Flex 22" stand - wall mounting or counter mounting.

Back to top

Additional Resources for the Flex 22" Counter Stand

Back to top

Related Articles
Toast Flex for Kitchen Installation Guide
Toast Flex 3 Installation Guide
Toast Flex 22 Installation Guide
Toast Flex and Elo: Stand Options and Mount
Install Your Replacement Toast Flex Terminal
Did this answer your question?