Skip to main content

Perform Solar Analysis

Count the hours of sun on your landscape and facades

Written by Holly Conrad Smith

Sun on open space and in living rooms is often a planning requirement, and it helps homes sell. Sun hours mode counts how many hours of sun each part of your site gets on a chosen day. It covers landscape, the rest of the ground, and building facades. Use it to check a design against a sun access rule before you submit it.

Run a sun hours analysis

  1. Open the Solar app and click Sun hours at the top. Giraffe starts counting right away.

  2. Click the date field under Date and Time and pick the day to test. The field shows the date and the time window, such as "21 Jun, 09:00 to 15:00 (6 h)".

  3. Set the time window on the chart. Drag the two horizontal lines to set the start and end times. Drag the vertical line, or click the chart, to change the date.

  4. Read the colors on the map and the numbers under Results.

The time window starts at 09:00 to 15:00. Each analysis covers one day. To compare seasons, such as the winter solstice and midsummer, run it once for each date.

Giraffe runs Sun hours again each time you change your design, the date, the time window, or a setting. While it runs, Calculating… shows beside Results.

Sun hours works in a project. It isn't available in a Space. Solar also pauses while you edit a block, and picks up again when you exit block editing.

Color the map by hours, pass/fail, or sun lost

Pick how Sun hours colors the map with Color by under Display:

  • Hours colors each surface by its hours of sun in the time window. The key under it shows the color for each hour, from dark blue for no sun through yellow to red.

  • Pass/fail colors each surface green where it gets enough sun and red where it doesn't. A surface gets enough sun when it reaches the minimum set by the rule that covers its usage, or by the Baseline everywhere else. Learn how to set the minimum sun with rules.

  • Lost colors the ground and existing buildings by the hours of sun your proposal takes away. Green marks surfaces that gain sun, because a demolished building shaded or covered them before. Your proposed buildings show in one flat color, labeled Proposed (not compared) in the key.

Lost needs to know which buildings are on the site today. Learn how to mark existing and demolished buildings.

Check the sun hours at a point

Turn on Hours at cursor under Display, then move the cursor over the map. A tag beside the cursor shows the hours of sun at that point, such as "4.5 h of sun". Hours at cursor is on by default and shows while the Solar app is open on screen.

See what blocks the sun at a point

Turn on Sun rays at cursor under Display. Giraffe draws a line from the cursor toward the sun at each time step. The key under the setting shows the color for Reaches the sun and for Blocked. The lines stay in place while you orbit the map, so you can turn the view and see what blocks each one.

Read the sun hours results

The Results group in Sun hours mode shows how much of each surface gets enough sun. The top table has a row for each kind of surface:

  • Landscape: all the landscape geometries in your project.

  • Other ground: the ground inside your project boundary that no landscape covers. This row shows when the project has a polygon boundary.

  • Facades: the walls of your buildings.

For each row, Mean is the average hours of sun. Sunny is the share of the area that gets at least its minimum sun. Landscape uses the minimum from the rule that covers its usage, or the Baseline. Other ground and facades use the Baseline, which starts at 3 hours. Hover over a Sunny value to see which minimum it uses.

Check each landscape area

Under the totals, the Landscape features table lists each landscape geometry with its Area, Mean hours, and Sunny share. Use it to find the open space that falls short.

  • Hover over a row to highlight that geometry on the map.

  • Click a row to select the geometry. Click the checkbox at the top to select them all.

  • Right-click a row and choose Fly to to move the map to it, or Select to select it.

See the share of each surface by hours

Click the chart button beside Results to open the sun hours chart. For each surface, it shows the share of the area that gets at least each number of hours of sun.

Fade or hide the sun hours colors

Sun hours colors sit on their own Sun hours layer in the Layer Palette. Change the layer's opacity to fade the colors, or hide the layer to see the map under them. Right-click the Sun hours layer and choose Turn off Sun hours to leave Sun hours mode.

When a building is missing from the results or Sun hours runs slowly, troubleshoot Solar.

Did this answer your question?