Topics to address:
-> Issues updating
In this article, you will find common issues and small troubleshooting steps to help you verify and diagnose your device.
Keep in mind that these steps don't immediately discard further testing that the support may request out of you, so please try your best to share the information as requested.
Rainbow LED
This issues can signal mainly two things:
This is a sign that your firmware has met an issue and is unable to finish the initial tests and calibrations necessary
Your motor is unresponsive or defective and the Handy is waiting for a reply from it, thus becoming stuck.
Because both root causes use the same signal, we need to a quick test to verify if this device is recoverable. Specifically, we need to tighten the screws that connect the motor to the internal support rod for the arm.
To do this, we need to follow these steps:
Turn off your Handy and move the arm until you can see the two screw holes at the bottom of the shaft. The screw we want to tighten is the bottom one.
Once it is accessible, using the 2 mm Hex Screwdriver, tighten the screw at the bottom.
After tightening the screw, remove the screwdriver and test the movement of the arm by manually moving it to ensure it still has upwards and downwards movement.
Now plug the device, it should try to calibrate itself and will initially show the Rainbow LED, but should go into a solid green Indicator once it reaches the bottom.
You can find a more complete guide with images in this article.
If this test does not result in your device being able to finish calibration, it likely means your device has a bigger defect on the motor or a severe Firmware failure. Both of which you cannot troubleshoot further and will need to contact support for next steps.
When reaching out to support, always include your Order Number and a video showcasing the issue.
Red and White LED
This means your device has a motor that is unable to calibrate, so it cannot tell where on the support rod it is located and as a result it cannot move.
This can happen to various reasons, but most commonly it is due to bad sensors on your device or an old motor not being able to properly tell where it is.
To make sure this is truly the main issue with your device, we need to give the motor a chance to properly calibrate by helping it a bit. Follow the instructions below to help it calibrate.
Turn off the device
Move the arm to the top of the device
Turn on the device
If the steps above do not work, repeat the process but leave the arm in the middle instead of the top.
If the steps above also do not works, repeat the process but leave the arm in the bottom of the device instead.
If necessary, you can find a video showcasing how to perform this test in this article.
If this does not help your device calibrate, then there is a deeper issue and you need to contact support for further help.
When reaching out to support, always include your Order Number and a video showcasing the issue, mention you already attempted the test in this article as well.
Potential Defective Motor
Sometimes, your motor may find itself struggling when there is little resistance on the arm itself or just move to the bottom once and then no longer be able to move, being extremely loud or other such scenarios.
By default, we always recommend performing common maintenance using the maintenance kit and the manual that comes along with it, you can find a copy of said manual here.
If this does not help solve the issues, please contact support using the chat box or email and make sure to include Order Number and a video showcasing the issue
Power Connector Issues
The Handy 1 is powered by an external power supply and if you find that your device is unable to turn on suddenly, it is worth verifying if the power supply is working correctly.
Luckily, this is easily replaceable. Any generic power supply with a plug using 5.5 mm x 2.5 mm connector should suffice. Use a different power supply to check if the root of the problem is on the Handy or not.
If this does not help solve the issues, please contact support using the chat box or email and make sure to include Order Number and a video showcasing the lack of power.
Connection Issues
Because we user servers to authenticate and connect devices, sometimes you can face issues with connection and due to the complexity, diagnosing can be hard to execute.
In general, we recommend doing the following tests
Test your connection using a Mobile Data Hotspot
The goal of this test is to verify that a different network or ISP is able to connect and communicate with our servers. This is the single most common issue with connection.Verify your Network settings
Your networks can sometimes have weird settings that can block or cause unseen complications with connection. Make sure your network isn't blocking any particular device through their MAC Addresses, that your network is on a 2.4 Ghz and not a hybrid between 2.4 and 5 Ghz, there is no other blocks based on your equipment.Funnel your devices in the network through a VPN
Laws and regulations cause regional blockages to happen, and the only known way to circumvent this is via a VPN that covers all devices in your network. While this is hard to execute, users with technical know how have found success in evading regional blocks using this method.
You can also find more tips and troubleshooting steps on this article.
If this does not help solve the issues, please contact support using the chat box or email and make sure to include Order Number and any and all troubleshooting steps you did, including any screenshots you can take showcasing error codes.
Try to include the UID and Connection Key for your device as well so we can verify information on the back end of the server for further clues and support.
Issues updating
Users that have issues updating their Firmware can try a few troubleshooting steps, but they are mostly all related to connection.
Try updating using the Handy Onboarding App
Try updating using the Handyverse website
If this does not help solve the issues, please contact support using the chat box or email and make sure to include Order Number, including any screenshots you can take showcasing error codes.
