Skip to main content

Building Pads and Ramps

Level the ground for buildings and grade roads on a slope

Written by Holly Conrad Smith

On a sloping site, every building needs level ground and every road needs a grade a car can drive. Building pads and ramps model that grading in Giraffe. Draw them and set their levels, and the Terrain app reshapes the ground and works out the cut and fill.

How geometries sit on the terrain

When 3D terrain is on, your geometries sit on the ground:

  • Flat geometries, such as landscape and roads, follow the terrain like fabric.

  • Buildings and other 3D geometries sit at the ground height under the middle of their footprint. On a slope, part of a building can float above the ground or sink into it.

  • A geometry with an Elevation Datum sits at that level.

To set a building on level ground, draw a building pad under it.

Draw a building pad

  1. Open the Terrain app and click 3D.

  2. Under Results, click Draw a pad or ramp at the bottom of the Volumes table.

  3. Draw the pad on the map with the Rectangle Tool or the Polygon Tool.

  4. Giraffe levels the ground inside the pad and adds a row for it to the Volumes table.

A new pad starts at the ground level at its middle. It uses the Building Pad usage when your project has one, or Generic 3D otherwise.

Draw a ramp

  1. Open the Terrain app, and under Results, click Draw a pad or ramp.

  2. Pick Line in the choice beside the drawing toolbar.

  3. Draw the ramp's center line on the map with the Polyline Tool. The first point you click is the ramp's start.

  4. Giraffe grades a road along the line and adds a row for it to the Volumes table.

A new ramp starts level, at the ground height at its middle. It has a 5 m road, a 2 m footpath on each side, and a 10 m corner radius at each bend. Set its Grade to make it climb.

Make any polygon or line a pad or ramp

Any polygon or line on a visible layer works as a pad or ramp when its Cut and Fill property is on. Select the geometry and turn on Cut and Fill under Terrain in the Property Palette. A polygon becomes a pad, and a line becomes a ramp.

Set a building pad's level and slope

Select a building pad to see its settings under Terrain in the Property Palette:

  • Elevation Datum: the pad's level at its middle. When it's blank, Giraffe uses the ground level at the middle.

  • Fall: how steeply the pad slopes, from 0% to 50%. The pad tilts as one flat plane about its middle. A small fall lets a pad drain.

  • Bearing: the compass direction the pad falls toward, in degrees from north.

  • Angle of Repose: the steepest slope of the batter where the pad meets the ground. It sets the batter for cut, and for fill unless you set Fill Angle. It starts at 45°.

  • Fill Angle: the steepest slope of the batter for fill. It follows Angle of Repose until you set it.

  • Cut and Fill Offset: grows the graded area outward from the pad's edge, or shrinks it with a negative value. It starts at 0.6 m.

When part of a pad is flatter than 0.5%, a warning under Bearing shows how much of it ponds, such as "Ponds over 120 m² (flatter than 0.5%)". Add some Fall to drain it.

Set a ramp's level and grade

Select a ramp to see its settings under Terrain in the Property Palette:

  • Elevation Datum: the ramp's level at its first point.

  • Grade: how steeply the ramp rises from its first point to its last, from -50% to 50%. A negative grade falls.

  • Road Width: the width of the road, without the footpaths. It starts at 5 m.

  • Footpath Width: the width of the footpath on each side of the road. It starts at 2 m.

  • Angle of Repose and Fill Angle: the steepest slopes of the batters beside the ramp, for cut and for fill.

  • Cut and Fill Offset: grows the graded area beside the ramp, or shrinks it with a negative value.

When one stretch of a ramp is steeper than its overall grade, Giraffe shows that stretch's grade under Grade, such as "Steepest stretch 9.5%".

Did this answer your question?